Part 111 LIQUID-METAL FUEL REACTORS I'rank Maspan, Editor Brookhaven National Laboratory 18. Liquid-Metal Fuel Reactors 19. Reactor Physics for Liquid-Metal Reactor Design 20. Composition and Properties of Liquid-Metal Fuels 21. Materials of Construction—Metallurgy 22, Chemical Processing 23. Engincering Design 24. Liquid-Metal Fuel Reactor Design Study 25. Additional Liquid-Metal Reactors R. Bourpnrav M. B. Bropsky J. 5. BRYNER J. CHERNICK J. G. Y. Coow 0. E. Dwyer W. P, EATHERLY J. J. Egax A, M. Egaya W. 8. GINELL L. GrREEN R. J. IsLER D. H. GURINKsY D. HaLn . B. HiLL CONTRIBUTORS M. JANES 0. F. KAMMERER C. J. KLamur R. M. Kieun R. L. MANSFIELD R. A. MEYER ¥F. T. MILEs C. RASEMAN W. RosBa D. G. SCHWEITZER T, V. SHEEHAN H. SusskinND C. Wane J. R. WEEKs R, H. WiswaiL PREIFACE This is the most extensive discussion of liquid-metal fuel reactor devel- opment yet published in the United States. Emphasis has been placed on the Liquid Metal I'uel Reactor being developed by Brookhaven National Laboratory and Babcock & Wilcox Co. because it is the most advanced project. Work on various phases of liquid-metal fuel reactors is being carried out by Los Alamos Scientific Laboratory, Raytheon Manufacturing Co., Argonne National Laboratory, Ames Laboratory, and Atomics International. The editor would like to have given more coverage to work at the last three locations but was unable to because time was lacking. The liquid-metal fuel reactor development at Brookhaven started as an organized program in 1951. Before that, work had been conducted on bismuth-uranium fuel and other components. In 1954, Babcock & Wilcox Co., in collaboration with representatives of sixteen other companies, prepared a reference design and report. In 1956, Babcock & Wilcox con- tracted with the Atomic Energy Commission to design, build, and operate a low-power experimental reactor (LMI'R Experiment No. 1). Research, development, and design studies are being carried on concurrently by B & W and Brookhaven. LMFR Experiment No. 1, on which construc- tion is scheduled to start in 1960, is intended to demonstrate feasibility and provide information on the physics, metallurgy, chemistry, and mechanical aspects of this type of reactor. The editor expresses appreciation to many of his colleagues at Brook- haven and Babcock & Wilcox for working with him on these chapters. He wishes particularly to thank those whose material he drew upon, also C. Williams, O. E. Dwyer, D. Gurinsky, H. Kouts, I'. T. Miles, and T. V. Sheehan, of Brookhaven National Laboratory; R. T. Schoemer, H. H. Poor, and J. Happell, of Babcock & Wilcox Co.; R. Rebholz and G. Goring, of Union Carbide Corp.; D. Hall, of Los Alamos Scientific Laboratory; and W. Robba, of Raytheon Manufacturing Co. Special appreciation is due Miss Gloria Ministeri for her laborious and prolonged secretarial work and Miss Dolores Del Castillo for coming to our aid in emergencies. Upton, New York Frank Maslan, Editor June 1958 CHAPTER 18 LIQUID METAL FUEL REACTORS 18-1. BAcKGROUND Liquid metal fuel reactors have received attention since the early days of reactor technology. The concept of a high-temperature fluid fuel which could be ecirculated for both heat exchange and chemical processing has been an intriguing one [1-1]. This type of reactor was first suggested in 1941 but received little research and development attention until approximately 1947. At this time the Nuclear Engineering Department at Brookhaven National Laboratory began its Liquid Metal Fuel Reactor (LMFR) development. A solution of uranium 1 bismuth was suggested because of the low melting point and low neutron-capture cross section of bismuth. Coupled with these factors 1s the very high boiling pommt of bismuth, which makes possible the high- temperature operation of a bismuth-cooled reactor at relatively low pressures, Modern steam power plants have a thermodynamic efficiency of approxi- nuitely 409¢. For a nuclear system to achieve comparable efficiencies, the working fluid will have to have a reactor outlet temperature in the neigh- borhood of 500°C. The LMIR is one of the new types of nuclear reactors having this desirable characteristic. Thus, it is one of the few with poten- tialities for producing power competitive with the best of the present steam systems. 18~1.1 Work at Brookhaven National Laboratory. In 1948, an appraisal of various low-melting alloys was made at Brookhaven. Attention was also given to metallie slurries consisting of uranium in the form of intermetallie compounds suspended in liquid metal carriers, The uranium-bismuth system appeared to show considerable promiise. Preliminary solubility studies were completed by 1950 and a start was made on fuel processing Investigations. Nince that time the project has steadily accelerated. Chemical aspects of the fuel and fuel-processing systems have been and are being investigated in considerable detail. Metallurgical studies of corrosion, mass transfer, and stability of fuel systems have advanced from short-time crucible tests to circulating loops of alloy steel operated for many thousands of hours. Consideration has also been given to the design of such various reactor components as pumps, piping, valves, heat exchangers, and instruments. 703 704 LIQUID METAL FUEL REACTORS [cHAP. 18 18-1.2. Work of study groups. In common with other reactor concepts, the LMI'R has been evaluated from time to time as part of the general Atomic Energy Commission Reactor Development Program. During the summer of 1953, the LM FR was evaluated under Project Dynamo, and it was concluded that 1t was an extremely attractive concept if proven tech- nically feasible. In 1955 an industrial study group, under the direction of Babeock & Wilcox, made a detailled appraisal and design of the LMFR concept [19], and reported that it could be proved technically feasible in the near future and that it appears attractive from an economic point of view. In 1957, the Babcock & Wilcox Company re-evaluated the LMI'R and found the outlook as good as indicated previously [21]. Of course, the development of a new reactor concept of this kind 1s a long-range program. Present plans call for a buildup of knowledge through the construction and operation of several LMI'R experiments. The first of these 1s currently being designed by Babecock & Wilcox. 18-2. GENERAL CHARACTERISTICS OoF Liuip METAL Fuern REacTORS* 18-2.1 Comparison of fluid- and solid-fuel reactors. In order to better understand the development and characteristics of the Liquid Metal Fuel Reactor, fluid- and solid-fuel reactors should be compared, and a distinetion should be made between the features of fluid fuels in general and those of liquid metal fuels in particular. A reactor using a fluid fuel may have the following advantages over one with solid-fuel elements: (1) Simple structure. A fluid fuel can be cooled in an external heat exchanger separate from the reactor core. Thus the nuclear requirements (of the core) and the heat flow requirements (of the exchanger) need not both be satisfied at the same place. This may allow design for very high specific power. For example, material of high cross section, such as tung- sten or tantalum, which could not be used in the core, could be used in the heat exchanger. (2) FKasy fuel handling. (3) Simplified reprocessing. The reduction to metal, fabrication, canning, and dissolving steps are eliminated. Because manual steps in refabrication are unnecessary, decontamination need not be complete. The cooling time could be made much shorter, resulting in a smaller holdup of fissionable material. (4) Simplified waste disposal. (5) Continuous removal of fission products. The removal of poisons would improve neutron economy and permit higher burnup. With a lower *(Contributed by F. T. Miles, Brookhaven National Laboratory. 18-2] CHARACTERISTICS OF LIQUID METAL FUEL REACTORS 705 inventory of radioactive material, the potential hazard would be decreased; this might reduce the size of the exclusion area required for safety. (6) Inherent safety and ease of control. Any liquid fuel which expands on heating gives an immediate negative temperature coefficient of re- activity. This effect is not delayed by any heat-transfer process. The rate of expansion 1s limited only by the speed of sound (shockwave) in the liquid. This instantaneous effect tends to make the reactor self-regulating. Adjustment of fuel concentration can be used as an operating control. Disadvantages of fluid fuels are listed below: (1) Possible fluctuations of reactivity caused by density or concentra- tion changes in the fuel, e.g., bubbling. (2) Loss of delayed neutrons in the fuel leaving the core. (3) External holdup of fissionable material. (4) Induced activity in pumps and heat exchangers and possible de- position of fuel and fission products. (5) Corrosion and erosion problems. Each fuel system has its particular corrosion problems. These differ greatly from one system to another, but in every case corrosion is a critical problem which must be solved. (6) Iligh radiation levels in the reactor and in the component piping require devclopment of remote maintenance techniques. 18-2.2 Advantages and disadvantages of LMFR. Comparing one liquid fuel system with another involves relative advantages and disadvantages. Liquid metal solution systems (in particular, solutions of uranium in bismuth) [5-12] have the following advantages over aqueous systems: (1) Metals can be operated at high temperatures without high pressures. (2) Metal solutions are free from radiation damage and do not give off bubbles. By using liquid metals, therefore, two factors that may limit the specific power of aqueous systems are avoided. (3) Liquid metals have better heat-transfer properties than water. (4) Metal systems do not have inherent moderating properties and can be used for fast and intermediate reactors as well as for thermal reactors, provided the critical mass requirements are not excessive. (5) Liquid metals can be circulated by electromagnetic pumps if desired, although the efficiency may be poor, as with bismuth. (G) Some suitable metals, e.g., bismuth, are cheaper than D-0O. (7) Polonium, formed from bismuth by neutron capture, may be a valuable by-product. Liquid-metal systems have the following disadvantages in comparison with aqueous systems: (1) The heat capacity is less than with water. (2) The higher density may be a disadvantage. (3) Liquid metals are more difficult to pump. 706 LIQUID METAL FUEL REACTORS [cHAP. 18 (4) The absorption cross sections of the best metals (e.g., bismuth g, = 0.032 barn) are inferior to D20, although better than H2O. The cross section of bismuth may be low enough, however, to allow breeding of U233 from thorium by means of thermal neutrons. (5) For a thermal reactor, moderator must be supplied. (6) The limited solubility of uranium in bismuth necessitates the use of enriched U230 or U2?3 as fuel. Uranium-238 or thorium cannot be held in solution in sufficient concentration to give internal breeding. (7) Because of items (4) and (5} above, liquid metal fuel reactors are at least 2 ft in diameter [13] and cannot be scaled down as far as aqueous reactors can. (8) The high melting point of most metals makes the startup of a reactor difficult. (9) Polonium may represent an additional hazard. However, if the polonium remains with the fission products, it should not add te the prob- lems already present. 18-3. Ligvip MEeTaL Frer REacTor TYpES As a solvent for liquid-metal fuels, bismuth is a natural choice because it dissolves uranium and has a low cross section for thermal neutrons. Asa result, research work at Brookhaven National Laboratory has centered on bismuth-uranium fuels. Other possible liquid-metal fuels are the Los Alamos Molten Plutonium System (LAMPRE) [14] and dispersions of uranium oxide in liquid metals, NalX [153] or bismuth [16]. The limited solubility. of uranium in bismuth is troublesome in some designs. More concentrated fuels can be obtained by using slurries or dispersions of solid uranium compounds in bismuth. Among the solids which have been sug- gested are intermetallic compounds [10] uranium oxide [16], uranium carbide, and uranium fluoride. Use of a dispersion avoids the limited con- centration but introduces other problems of concentration control, sta- bility, and erosion. Liquid metal fuel reactors would appear to be most useful for large central station power plants [6,11,17-20] where the integrated chemical processing, one of the attractive features of an LMFR system, would be important. The uranium-bismuth fuel system is flexible and can be used in many designs. Although other types of liquid-metal systems are certainly possible, the LMFR at Brookhaven is being designed as a thermal reactor in which the fuel is dissolved or suspended in a liquid heavy-metal carrier. Ordi- narily, the liquid metal is bismuth for highest neutron economy, but other systems such as lead or lead-bismuth eutectic may be used. The moderator is graphite, although beryllium oxide has also been considered. 18-3] LIQUID METAL FUEL REACTOR TYPES 707 | LMFR r———_—_—----——-——— S I SIS SR infegrul‘ | Externally Cooled | Internaily Cooled {Pot-Type) | One Fluid ! Two Fluid 1 1 Slightly . U-Bi or Th-Bi or| | Solid Th ;'T“ Enriched Ul"_3' UQ,.-Bi UTh | 1 1ho.,-8i | | Blanket vy U-Slurry Solution Slurry Shurry Slurry Elements Fic. 18-1. Classification of Liquid Metal Fuel Reactors. Liquid metal fuel reactors are classified on the basis of their heat- transfer characteristics (Fig. 18-1) [21]. If heat is transferred within the core the reactor is said to be internally cooled. If heat is transported by the fuel to the primary heat exchanger external to the core, the reactor is externally cooled. The term “‘integral reactor’” implies an externally cooled system, but one so compact that the reactor and primary heat exchangers can be placed in the same container. Iixternally cooled LMFR’s can be divided into two classes, single-fluid and two-fluid. In the single-fluid reactor the fissionable and fertile ma- tertals are combined in a single fluid carrier, bismuth. This type of reactor has no separate blanket, and conversion or breeding takes place within the core fluid itself. The conversion ratio can be made to approach unity with the proper choice of such parameters as core size, graphite-to-fuel ratio, and thorium concentration. However, the most economic design is not neces- sarily the one having the highest conversion ratio (see Chapter 24). If no fertile material is mixed with the fuel, the concept reduces to the simple burner. The two-fluid externally cooled LMFR (Fig. 18-2) is somewhat more complex because it has a physically separate core and blanket, but higher conversion ratios are possible. The blanket can be made in a variety of ways, making use of either solid or liquid blanket materials. In exploiting the LMEFR concept to the full, a fluid blanket consisting of a slurry of ThBis or ThOg in bismuth is used. A variety of fuels is also possible. In the two-region reactor, critical concentrations of uranium in bismuth could be below solubility limits; 708 LIQUID METAL FUEL REACTORS [cuaPp. 18 J’“—MM ‘ ) .~ Radioactive -~ Vac Salt Fuel Bi-U233. F ps 3.\ Gas Storqge ‘ Pumps fi Fpsl Process f;T i Po P ] ump Xenon Salt Trup U Concn |Bi-U233 Sh[l EXCESS U233 Control - ‘?‘:’ \ Bi-Po Steam Plant S e ; Trap L U233 parg : ~ Storage 4~Pump(s) # (L: Y o Bi-Th3Bi3-Po233.U233.Fp's ( | Storage - | 4233 Blanke! | .n.'... 1\ ) r Bi-Th3Bis U233 Th3 Bis-Bi 1: ‘ ' Blanket ~ % H Il _:“,":'/.c Bianket + FP's Process Graphite ’ L - - Moderator Salt Thflf Bi-UZ233 Fyel Fic. 18-2. Schematic diagram of LMFR, showing reactor, steam plant, and chemical processing. therefore solution fuels are possible. Such a fuel for the single-region re- actors is possible only for small thorium loadings or for burners. Higher fuel concentrations can be utilized only through the use of slurries. On the basis of experiments, a maximum slurry content of 10 w/o (weight percent) of either uranium or thorium as bismuthide compounds in bismuth can be assumed. If an oxide slurry is used, approximately 20 w/o can be carried by the bismuth. So far only fuels of U233 and U235 have been investigated in the LMFR program. 184. LMFR Procram In the following chapters detailed discussions of the liquid metal fuels research, development, and engineering work are given. Practically all the LMFR work is in the research and development stage. In the first group of chapters, the physics, chemistry, and engineering design of the LMFER are discussed. In the last chapters, several liquid metal fuel re- actor designs, based on current research and development, are presented. It should be understood that these are design studies and it is expected that more than one liquid metal fuel experimental reactor will have to be built and operated before a final commercial design is evolved. REFERENCES 709 REFERENCLS 1. H. Harpax and L. Kowarski, Cambridge University, England, Cavendish Laboratory, 1941. Unpublished. 2. M. B Le, Fairchild Engine & Airplane Corp.,, NIEPA Division, 1950. ['npublished. 3. E. P. WienuR et al., Argonne National Laboratory, 1944, Unpublished. 4. G. Youna, Outline of a Liquid Melal Pile, USALC Report MonP-264, Oak Ridge National Laboratory, Mar. 5, 1947, 5. 0. E. Dwyer, Heat Transfer in a Liquid-Metal-Fuel Reactor for Power, in Chemical Engineering Progress Symposium Series, Vol. 50, No. 11. New York: American Institute of Chemical Iingineers, 1951, (pp. 75-91) 6. C. Wirnrams and F.o T Mines, Liquid Metal Tuel Reactor Systems for Power, ibid., No. 11, (pp. 244-252) 7.5 D Arnesrroxn et al,, Studies in the Uranium-Bismuth Fuel System, ibid., No. 120 (p. 23) 8. (. J. Rasemax and J. Wemsaan, Liquid-Metal-I'uel Reactor Processing Loops, ibid., No. 12, (p. 153) 9. D. W. Bareis et al., Processing of Liquid Bismuth Alloys by Fused Salts, ibid., No. 12, (p. 228) 16. R. J. Trrrern et al., Liquid-Metal Fuels and Liquid-Metal Breeder Blan- kets, 1bid., No. 13, (p. 11) 1. Nvcrear ENGINEERING DEPARTMENT, BROOKHAVEN NATIONAL LABORA- rory, Liquid Metal Fuel Reactor Systems, a collection of seven papers, Nucleonics 12(7), 11-12 (1954). 12, 0. E. Dwyer et al., Liguid Bismuth As a Fuel Solvent and Heal Transport Medium for Nuclear Reactors, paper presented at the Nuclear Engincering and Scienee Congress at Cleveland, Ohio, Dec. 12-16, 1955, (Preprint 50) 13. J. Cueryick, Small Liquid Metal Fueled Reactor Systems, Nuclear Ser. and I'ng. 1, 135-155 {1956). I4. R. M. Kienn, .4 Molten Plutontum Reactor Concept— LAMPRE, USAEC Report LA-2112) Los Alamos Scientific Laboratory, January 1957: Los Alamos Molten Plutonium Reactor Equipment (LAMPRID), Nucleonies 14(2), 14 (February 1956); Molten Plutonium Reactors, in Radialion Safety and Major Activiites tn the Alomic Inergy Programs, July—December 1956, U, S. Atomic Iinergy Commigsion. Washington, D. C.: Government Printing Office, January 1957. (p. 43) 15. B. M. Asranam et al,, UOo-NalX Slurry Studies in Loops to 600°C, Nuclear Sci. and Eng. 2, 501-512 (1951). 16. J. K. Davipson et al., A UOg-Liquid Metal Slurry for Economic Power, paper presented before the American Nuclear Society at Washington, D. C., Dec. 10-12, 1956. 17. F. T. MiLes and C. WinLiams, Liquid Metal Fuel Reactor, in Proceedings of the International Conference on the Peaceful Uses of Atomic Energy, Vol. 3. New York: United Nations, 1956. (P/494, p. 125) 710 LIQUID METAL FUEL REACTORS [cHAP. 18 18. D. J. SunaesTaken and . Duruam, Liquid 3Metal Fuel Reactor for Central Station Power, paper presented at the Nucelear Engineering and Scienee Congress at Cleveland, Ohilo, Dee. 12-16, 1955, (Preprint 39) 19. Barcock & Wircox Co., Liquid Metal Fuel Reactor; Technical Feasibility Report, USALC Report BAW-2(Del)), June 30, 1955, 20, . Mars et al., Preliminary Design of an LMFR Power Plant, Nuclear Set. and Eng., in preparation. 21. Bascock & Wincox Co., 1958. Unpublished.